野兽帝国
发表于 2011-8-19 09:31
webcxc 发表于 2011-8-19 10:27 static/image/common/back.gif
前阵子和几间软件公司开会,几乎清一色的thinkpad
唯有一个人,用的mbp
连上投影一看,里面装的还是windows...
zj7776
发表于 2011-8-19 09:34
Grundig 发表于 2011-8-19 10:21 static/image/common/back.gif
我想买i7的。。i5的觉得不够用。。
http://www.notebooksbilliger.de/pcsysteme/all+in+one+pcs/ab+58cm+23/hp+7300+elite+mct+intel+core+i7+2600
770 Euro
http://www.notebooksbilliger.de/pcsysteme/all+in+one+pcs/ab+58cm+23/products_id/85105
850 Euro
http://www.notebooksbilliger.de/notebooks/sony_100/sony+vaio+pcs/dell+vostro+460+intel+core+i7+2600+78777
850 Euro
2ma31547
发表于 2011-8-19 11:02
Grundig 发表于 2011-8-19 09:28 static/image/common/back.gif
运行类似于cst ansys这类的电磁仿真软件 模型的话是圆柱形 2米高 直径400mm不到。。。
要看模型有多少Element,不是看模型的外形尺寸。
不了解电磁方面的仿真,要是力学方面的还能给你建议。
还是建议买品牌的,要不然运行大型计算的时候,机器不稳定就会很头疼。
一万
发表于 2011-8-19 11:31
话说,在某教授执着之下,连秘书都用IMAC一体机,可她也就用来收发邮件看个网页.....唉...
Grundig
发表于 2011-8-19 11:42
2ma31547 发表于 2011-8-19 12:02 static/image/common/back.gif
要看模型有多少Element,不是看模型的外形尺寸。
不了解电磁方面的仿真,要是力学方面的还能给你建议。
...
我现在因为用自己的T410在那里仿真 大概是200w个element。。。觉得配置不行 没法提高仿真精度 我希望能到1到2千万的网格数
2ma31547
发表于 2011-8-19 11:56
Grundig 发表于 2011-8-19 12:42 static/image/common/back.gif
我现在因为用自己的T410在那里仿真 大概是200w个element。。。觉得配置不行 没法提高仿真精度 我希望能到 ...
200W个Element的电磁方面的计算,在T410 要运行多长时间呢?
webcxc
发表于 2011-8-19 12:48
野兽帝国 发表于 2011-8-19 10:31 static/image/common/back.gif
前阵子和几间软件公司开会,几乎清一色的thinkpad
唯有一个人,用的mbp
连上投影一看,里面装的还是window ...
{:5_386:}那还不如买别的的
momo_zhang
发表于 2011-8-19 13:12
野兽帝国 发表于 2011-8-19 10:31 static/image/common/back.gif
前阵子和几间软件公司开会,几乎清一色的thinkpad
唯有一个人,用的mbp
连上投影一看,里面装的还是window ...
那个人太丢脸。。。
swiss_yang
发表于 2011-8-19 13:40
Thinkpad or thinkcenter are the best option.
Since you will run some relative big simulation on the computer , the ability of heat transfer is therefore very important.
Another point must pay attantion, you must choose the 64bit operation system, because even if you have a 32 bit - computer with 4GB or 8GB RAM, the utility is always limited up to 3GB RAM.
Our IT support made a big mistake cause us lots of problem.
swiss_yang
发表于 2011-8-19 13:46
本帖最后由 swiss_yang 于 2011-8-19 14:46 编辑
Grundig 发表于 2011-8-19 09:28 static/image/common/back.gif
运行类似于cst ansys这类的电磁仿真软件 模型的话是圆柱形 2米高 直径400mm不到。。。
your domain is not big.
I am running a simulation now using ANSYS. The flow domain is a cylionder with diameter 500 m und height 500 m. of course my cell is a little bit coarse.
My computer is ThinkCenter with Quad Core